Miura Giken CB-302 Glamorous Cavity Iron
|
This one-piece cavity head is made by soft iron forging, and features a glamorous cavity shape that challenges the limits of the forging process. |
Although it has a shape with a strong sense of volume, it achieves a high level of both forgiveness and operability through effective weight distribution within the cavity for each count and a sole design that allows for easy release. |
Introducing the CB-302, a head that can be used to the fullest by everyone from average golfers to advanced golfers. |
The cavity is V-shaped, centered directly behind the impact area, and the weight is effectively distributed between the toe and heel, taking into consideration the functionality required for each count.
The head shape allows the entire head weight (=power) to be transmitted to the ball without loss during impact. The 160g weight (#7: blue part in the image above), which is 60% of the total weight of the head, is distributed to the extremely deep cavity sole. This is an increase of 1Og compared to the sole weight of the CB-301, achieving an even lower center of gravity.
Although the launch angle is high, the well-thought-out cavity shape allows for a strong ball trajectory that resists wind.
The sole width (#7: head center part) exceeds that of CB-301, achieving 19.8mm, the largest in the history of MG irons for an integrated soft iron forged head, and providing tolerance against head entry errors.
To address the problem of head slippage, which is a concern with wide sole heads, we have adopted a camber sole with a rounded back face side, providing a firm bounce effect while pursuing good slippage.
It is less affected by the grass and lie conditions and allows you to swing comfortably.
The sole shape has wide adaptability to swing trajectory and head incidence angle, and can accommodate golfers with a wide range of swing types.
The face length is 2mm shorter than CB-301 to 71.5mm. And the heel height is 1mm higher, to 34mm. It is a head that can be used by a wide range of target groups, as it has a small size and good operability, while achieving high straightness with little left and right ball wobbling.
The address view has a rounded overall outline, while the blade part has a strong and voluminous impression, similar to the back face.
The moderate offset, the volume of the heel, and the beautiful connection of the surfaces that wrap around the ball create a sense of unity throughout the club, creating an exquisite sense of calm and gentleness at address.
We have optimized the weight distribution on the back face to match the performance required for each count.
The weight on the toe side and heel side is changed depending on the count, starting from the V-shaped top of the sole.
The long iron has a weight distribution that makes it easy to turn the head and makes it difficult for the ball to go out to the right, while the short iron has a weight distribution that makes it easy to control the trajectory of the ball without getting caught too far to the left even if it goes down firmly. It has become.
We actively use the weight, which accounts for 60% of the entire head, to achieve the required performance.
Price: ¥25,000+tax (¥27,500 tax included)/1 piece
*We cannot sell the head alone.
*Weight may vary slightly
Double counter design [Improved meet rate]
Easily control "heavy" and "light".
The metal is perfectly blended at the tip of the shaft and in the grip. Light objects feel heavy, making it easier to swing and increasing the hit rate, and heavy objects feel lighter, making it easier to swing and increasing head speed.
Achieves optimal weight distribution to suit the type of golfer.
FLAT FLEX design [directional stability]
Use the same swing from driver to iron.
Conventional golf clubs have different shaft vibrations for each club number, which causes the shot to lack stability. Therefore, we have adopted the "FLAT FLEX design" that makes the shaft vibrations uniform from the driver to the sand wedge. This completely new approach allows for further evolution of "flying" and "score improvement."
[Improved ball catchability]
With conventional shaft shapes, the tolerance for the KP was limited to ±10mm, but by moving the KP 60mm to the tip, it is possible to increase initial velocity and catch.
GR351 IR Product Specifications
Hardness |
R |
S.R. |
S |
H/S suitability |
32~36 |
37~40 |
41~44 |
Weight (g) LG |
43 |
44 |
45 |
Weight (g) MD |
41 |
42 |
43 |
Weight (g) ST |
39 |
40 |
41 |
KP |
Ultra-advanced |
torque |
5.5 |
Five |
4.5 |
Frequency (LG/MD/ST) |
206/209/212 |
224/228/232 |
242/246/250 |
Product Manager LG |
978 |
978 |
978 |
Product Director MD |
940 |
940 |
940 |
Product Length ST |
902 |
902 |
914 |
B-100 |
14.8 |
14.9 |
15 |
Price: ¥36,000 (excluding tax) / 1 bottle
* (LG-#3/#4/#5 MD-#6/#7/#8 ST-#9/#10/A/S)
*Tip diameter 9.46 after painting *Frequency is 60 degree method DR-46/D2 FW-43/D1 UT-40/D1 IR LT-#5 38/D1 MD-#7 37/D0 ST-#9 36/D0
*Product specifications are subject to change without notice.