Miura Giken CB-302 Glamorous Cavity Iron
|
This one-piece cavity head is made by soft iron forging, and features a glamorous cavity shape that challenges the limits of the forging process. |
Although it has a shape with a strong sense of volume, it achieves a high level of both forgiveness and operability through effective weight distribution within the cavity for each count and a sole design that allows for easy release. |
Introducing the CB-302, a head that can be used to the fullest by everyone from average golfers to advanced golfers. |
The cavity is V-shaped, centered directly behind the impact area, and the weight is effectively distributed between the toe and heel, taking into consideration the functionality required for each count.
The head shape allows the entire head weight (=power) to be transmitted to the ball without loss during impact. The 160g weight (#7: blue part in the image above), which is 60% of the total weight of the head, is distributed to the extremely deep cavity sole. This is an increase of 1Og compared to the sole weight of the CB-301, achieving an even lower center of gravity.
Although the launch angle is high, the well-thought-out cavity shape allows for a strong ball trajectory that resists wind.
The sole width (#7: head center part) exceeds that of CB-301, achieving 19.8mm, the largest in the history of MG irons for an integrated soft iron forged head, and providing tolerance against head entry errors.
To address the problem of head slippage, which is a concern with wide sole heads, we have adopted a camber sole with a rounded back face side, providing a firm bounce effect while pursuing good slippage.
It is less affected by the grass and lie conditions and allows you to swing comfortably.
The sole shape has wide adaptability to swing trajectory and head incidence angle, and can accommodate golfers with a wide range of swing types.
The face length is 2mm shorter than CB-301 to 71.5mm. And the heel height is 1mm higher, to 34mm. It is a head that can be used by a wide range of target groups, as it has a small size and good operability, while achieving high straightness with little left and right ball wobbling.
The address view has a rounded overall outline, while the blade part has a strong and voluminous impression, similar to the back face.
The moderate offset, the volume of the heel, and the beautiful connection of the surfaces that wrap around the ball create a sense of unity throughout the club, creating an exquisite sense of calm and gentleness at address.
We have optimized the weight distribution on the back face to match the performance required for each count.
The weight on the toe side and heel side is changed depending on the count, starting from the V-shaped top of the sole.
The long iron has a weight distribution that makes it easy to turn the head and makes it difficult for the ball to go out to the right, while the short iron has a weight distribution that makes it easy to control the trajectory of the ball without getting caught too far to the left even if it goes down firmly. It has become.
We actively use the weight, which accounts for 60% of the entire head, to achieve the required performance.
Price: ¥25,000+tax (¥27,500 tax included)/1 piece
*We cannot sell the head alone.
*Weight may vary slightly
The new DG series (DG95/DG105/DG120) was developed over a period of more than three years. By adopting new materials, heat treatment, Variable Wall Technology (VWT), an original shaft that varies the thickness in multiple places, and a new step pattern, the new DG series offers the same feeling as the previous Dynamic Gold model while achieving even greater performance.
In particular, the DG95 model, which was released first in Japan, is lightweight at around 90g, but by having a similar stiffness curve to the conventional DG model, it achieves the same stickiness and controllability as the DG, despite being a lightweight shaft.
The greatest advantages of lightweight shafts -- ease of swing and distance -- have been further improved, and by setting the kick point at a mid-kick point for the DG95 and at a kick-kick point for the DG105/120, we have achieved a balance with controllability. |
*Do not wipe the printed surface with solvents such as thinner, as this may cause the printing to peel off.
Please note that the print may peel off depending on the length of use and the conditions of use.
Dynamic Gold 95
Application |
Tip |
flex |
Shaft length |
Tip Diameter |
Butt Diameter |
Weight before cutting |
Weight after cutting |
Kick Point |
iron |
taper |
S200 |
38.5-35.0 (978-889) |
.355 inch (9.00mm) |
.600 inch (15.25mm) |
95g |
— |
Mid-tone |
iron |
taper |
R300 |
38.5-35.0 (978-889) |
.355 inch (9.00mm) |
.600 inch (15.25mm) |
95g |
— |
Mid-tone |
Dynamic Gold 105
Application |
Tip |
flex |
Shaft length |
Tip Diameter |
Butt Diameter |
Weight before cutting |
Weight after cutting |
Kick Point |
iron |
taper |
X100 |
41.0-37.0 (1,041 -940) |
.355 inch (9.00mm) |
.605 inch (15.37mm) |
105g |
— |
Original condition |
iron |
taper |
S200 |
41.0-37.0 (1,041 -940) |
.355 inch (9.00mm) |
.600 inch (15.25mm) |
103g |
— |
Original condition |
iron |
taper |
R300 |
41.0-37.0 (1,041 -940) |
.355 inch (9.00mm) |
.600 inch (15.25mm) |
101g |
— |
Original condition |
Dynamic Gold 120
Application |
Tip |
flex |
Shaft length |
Tip Diameter |
Butt Diameter |
Weight before cutting |
Weight after cutting |
Kick Point |
iron |
taper |
X100 |
41.0-37.0 (1,041 -940) |
.355 inch (9.00mm) |
.600 inch (15.25mm) |
120g |
— |
Original condition |
iron |
taper |
S200 |
41.0-37.0 (1,041 -940) |
.355 inch (9.00mm) |
.600 inch (15.25mm) |
118g |
— |
Original condition |
iron |
taper |
R300 |
41.0-37.0 (1,041 -940) |
.355 inch (9.00mm) |
.600 inch (15.25mm) |
116g |
— |
Original condition |
Introducing the lightest Dynamic Gold ever, the DYNAMIC GOLD 85! Using new alloys and manufacturing processes, we have finally succeeded in developing the lightest Dynamic Gold ever, and have added it to the DG series as the new product Dynamic Gold 85!
Simply making the shaft lighter does not make it "Dynamic Gold". Dynamic Gold is especially popular among tour professionals and top athlete golfers, and must meet strict requirements to ensure it performs at its best under any circumstances. Thanks to its accumulated track record and know-how cultivated on the professional stage, Dynamic Gold 85 has cleared all of these requirements and has succeeded in achieving the maximum ball initial velocity, launch angle, and flight distance of any shaft in the 80g range.
The butt diameter is set thinner than comparable products from other companies to improve the impact sensation and tune it for a softer feeling. In addition, the tip is about 18% softer than other products, resulting in a high trajectory and smooth impact.
Even if you currently use a carbon shaft, you can enjoy the performance that only a steel shaft can provide with the Dynamic Gold 85, the lightest Dynamic Gold shaft ever, created using a new alloy and manufacturing process.
|
flex |
Product Manager |
Weight before cutting (g) |
Butt diameter (mm) |
Tip diameter (mm) |
Kick Point |
DG85IS2-HT |
S200 |
35.0-38.5 inches (889-978 mm) |
87 |
14.70 |
9.00 |
Medium tone |
DG120IS-HTS2-V |
R300 |
35.0-38.5 inches (889-978 mm) |
86 |
14.70 |
9.00 |
Medium tone |