|
Miura Giken CB-302 Glamorous Cavity Iron
|
| This one-piece cavity head is made by soft iron forging, and features a glamorous cavity shape that challenges the limits of the forging process. |
| Although it has a shape with a strong sense of volume, it achieves a high level of both forgiveness and operability through effective weight distribution within the cavity for each count and a sole design that allows for easy release. |
| Introducing the CB-302, a head that can be used to the fullest by everyone from average golfers to advanced golfers. |
The cavity is V-shaped, centered directly behind the impact area, and the weight is effectively distributed between the toe and heel, taking into consideration the functionality required for each count.
The head shape allows the entire head weight (=power) to be transmitted to the ball without loss during impact. The 160g weight (#7: blue part in the image above), which is 60% of the total weight of the head, is distributed to the extremely deep cavity sole. This is an increase of 1Og compared to the sole weight of the CB-301, achieving an even lower center of gravity.
Although the launch angle is high, the well-thought-out cavity shape allows for a strong ball trajectory that resists wind.
The sole width (#7: head center part) exceeds that of CB-301, achieving 19.8mm, the largest in the history of MG irons for an integrated soft iron forged head, and providing tolerance against head entry errors.
To address the problem of head slippage, which is a concern with wide sole heads, we have adopted a camber sole with a rounded back face side, providing a firm bounce effect while pursuing good slippage.
It is less affected by the grass and lie conditions and allows you to swing comfortably.
The sole shape has wide adaptability to swing trajectory and head incidence angle, and can accommodate golfers with a wide range of swing types.
The face length is 2mm shorter than CB-301 to 71.5mm. And the heel height is 1mm higher, to 34mm. It is a head that can be used by a wide range of target groups, as it has a small size and good operability, while achieving high straightness with little left and right ball wobbling.
The address view has a rounded overall outline, while the blade part has a strong and voluminous impression, similar to the back face.
The moderate offset, the volume of the heel, and the beautiful connection of the surfaces that wrap around the ball create a sense of unity throughout the club, creating an exquisite sense of calm and gentleness at address.
We have optimized the weight distribution on the back face to match the performance required for each count.
The weight on the toe side and heel side is changed depending on the count, starting from the V-shaped top of the sole.
The long iron has a weight distribution that makes it easy to turn the head and makes it difficult for the ball to go out to the right, while the short iron has a weight distribution that makes it easy to control the trajectory of the ball without getting caught too far to the left even if it goes down firmly. It has become.
We actively use the weight, which accounts for 60% of the entire head, to achieve the required performance.
Price: ¥25,000+tax (¥27,500 tax included)/1 piece
*We cannot sell the head alone.
*Weight may vary slightly
Product Concept
We developed "MCI BLACK" with the desire to allow golfers to experience the joy of hitting long irons and to use the entire iron set from top to bottom.
Until now, the weight of conventional iron shafts, including steel shafts, was the same regardless of the club number. As a result, the long irons tended to be too heavy and difficult to grip, while the short irons tended to be too light and cause mistakes.
To eliminate this mistake, the MCI BLACK shaft has a weight flow, and we have succeeded in creating a flow in weight, balance, and vibration frequency for each club. By aligning the swing feel of all clubs from drivers to wedges, we have made it possible to set up clubs that allow you to enjoy golf without any discomfort.
Features of "MCI BLACK"
1. Unified swing feel for all clubs, from drivers to wedges
We have succeeded in making the shaft weight flow, which is generally recommended, flow completely from the driver to the wedge. With conventional iron shafts, the weight was fixed, so the weight flow throughout the entire club was not possible. By using "MCI BLACK", it is possible to create a weight flow even within the iron set, achieving the same swing feel from the driver to the wedge. It is easier to bite into the center, resulting in an ideal launch.
2. Long irons are easy to swing and gentle
What is noteworthy is the improved ease of swinging long irons. With conventional shafts, the large weight difference between woods and UTs was one of the reasons why they were difficult to hit. By properly balancing the weight difference from UT to irons, it is easy to grip even with long irons, and a comfortable swing makes for high maneuverability.
3. Short irons are easy to feel the weight of, preventing them from catching too much The short irons, which tend to be too light and tend to be smashed with the hand, are now designed to feel heavy. Even when swinging with all your might, there is no need to worry about them catching too much, allowing for stable impact and maneuverability. |
