The birth of a legendary sword. Kamui KAMUI KP-01 Driver

Based on the latest club trends of high weight and high sensitivity, it adopts a pear-shaped head shape that is easy to hit, characteristic of KAMUI.

The weight of the face and body has been reduced to the bare minimum, and the excess weight is then used to lower the back sole. It is installed at a deep position as a power anchor, achieving a low and deep center of gravity.

Even against the odds, it slowly moves forward like a ball.

We can confidently recommend this club to golfers who create a lot of backspin and have trouble increasing their distance due to break to the right the ball.

Even against the wind, it slowly moves forward like a ball.

The deep back shape and the power anchor weight of over 30g are attached low and deep in the head, achieving a low and deep center of gravity.
Forgiveness on off-center hits and optimal spin.

High strength, high elasticity, toughness, wide high initial velocity area

Zirconium titanium is subjected to a special strengthening heat treatment to create a material with properties that combine the strength to bounce the ball off with force, the toughness to bend the face, and the elasticity to quickly return the bent face to its original position.
In addition, the 360° full cup face structure with no welds on the face surface achieves a wide high initial velocity area.

High rigidity and excellent vibration damping function

The honeycomb mesh structure around the power anchor increases the rigidity of the area around the anchor, providing a firm hold.
By incorporating it into the thin toe and heel areas, vibrations around the head are absorbed,
The ball provides a solid, satisfying feel and a calm, crisp sound when impacted.

Launch direction correction dimple

The two depressions on the toe and heel help prevent unnecessary distortion when hitting off-center.
The face flexes beautifully to correct the launch direction and optimize the amount of compression of the ball, minimizing the loss of distance.








The speed shaft that inherited the original FE and RB, enters the third generation of the series!

FireExpress RR-B

Fire Express is one of the first to use cutting-edge materials and continues to create shafts that increase speed and hit rate with groundbreaking designs and also have a comfortable swing. Their speed shafts have finally evolved into the third generation.

The Fire Express RR-B uses many TORAYCAR series materials such as T1100G, M50J, M40S, M30S, and TORAYCAR M40X, the most advanced material indispensable for premium shafts. The latest design increases the high elasticity ratio in the lamination, and effectively arranges multi-axis woven fabric sheets such as six-axis and four-axis, as well as tungsten powder sheets, making it easier to swing and contributing to increased distance and improved directionality.

By analyzing the material properties of the TORAYCAR series, we have succeeded in increasing rigidity while reducing the weight at each weight range. The outer layer is wrapped with a six-axis woven fabric sheet along the entire length, and the grip part is further wrapped with a four-axis woven fabric for a ten-axis structure. It effectively creates a pause from the turn and increases speed.

The middle section has a six-axis woven fabric sheet, creating a double six-axis structure. This controls the shaft trajectory during the swing and ensures accurate impact.

Furthermore, a tungsten powder sheet is attached from the middle to the tip. By controlling the center of gravity, it promotes ease of swing and acceleration of the tip. The optimal weight distribution based on the scientific study of swing trajectory and shaft flex return allows you to run through the impact at high speed.

The weight range is 4 types, including the 40g "Special" with 1 flex after testing, the 50 and 60g TX (Tour X) lineup, and the 70g range that has a strong following. The exterior is blue on the grip side to evoke a sense of speed, silver in the middle, and a clear coating on the tip that allows you to see the woven fabric.







・Made in Japan
-Chip parallel length is 50mm.
・The vibration frequency is an estimate when assembled with a head of 198g and 45.75 inches (measured using the 60-degree method).
-For adjustable clubs, the numbers may change significantly due to factors such as the shallow insertion of the hosel.
・The tip diameter is the bare tube value before painting.

Price: ¥58,000 (excluding tax) / 1 bottle